onderhoud fxstb1450 van 2001
- Onderwerp starter Maiky
- Startdatum
waar wil je hem dan leeg laten lopen
Dop los en het ding een half uur op zijn kop zetten.Werkt bij mij altijd.
Een stop in een Harleycarter???
Sick
MF veteraan
murph het is een twinky,die schijnen dat inderdaad te hebben.(zelf nog niet aan gewerkt gelukkig)
ts wat wil je nou eigenlijk je olie verversen of niet?
dan zal je toch ook die olie uit dat tankje moeten halen.......
of je brent hem naar je dealert(tm)
ts wat wil je nou eigenlijk je olie verversen of niet?
dan zal je toch ook die olie uit dat tankje moeten halen.......
of je brent hem naar je dealert(tm)
- 19 mei 2001
- 16.367
- 12.952
1. Start and run the engine for approximately ten minutes
or until the engine has reached normal operating temperature.
Turn the engine off and allow the oil to settle in the
oil tank. Support the motorcycle so that the oil can drain
completely.
CAUTION
Before removing the oil filler cap, clean off
all dirt and debris around it.
2. Remove the oil filler cap (Figure 5) to speed up the
flow of oil.
CAUTION
To avoid burning hands and arms, work
quickly and carefully when removing the oil
tank plug.
NOTE
The oil tank is equipped with an oil drain
line and hose that is connected to a fitting on
the rear right side of the frame (Figure 8).
3. Place a drain pan underneath the oil tank drain line
(Figure 9) drain plug, and remove the engine oil drain
plug and O-ring (Figure 10).
LUBRICATION, MAINTENANCE AND TUNE-UP 65
3
8 OIL TANK DRAIN
Drain plug
or until the engine has reached normal operating temperature.
Turn the engine off and allow the oil to settle in the
oil tank. Support the motorcycle so that the oil can drain
completely.
CAUTION
Before removing the oil filler cap, clean off
all dirt and debris around it.
2. Remove the oil filler cap (Figure 5) to speed up the
flow of oil.
CAUTION
To avoid burning hands and arms, work
quickly and carefully when removing the oil
tank plug.
NOTE
The oil tank is equipped with an oil drain
line and hose that is connected to a fitting on
the rear right side of the frame (Figure 8).
3. Place a drain pan underneath the oil tank drain line
(Figure 9) drain plug, and remove the engine oil drain
plug and O-ring (Figure 10).
LUBRICATION, MAINTENANCE AND TUNE-UP 65
3
8 OIL TANK DRAIN
Drain plug
- 19 mei 2001
- 16.367
- 12.952
4. Allow the oil to drain completely.
5. To replace the oil filter (Figure 11), performthe following:
a. Temporarily install the drain bolt and O-ring, and
tighten the bolt finger-tight. Then move the drain
pan underneath the front portion of the crankcase
and the oil filter.
b. At the front left side of the engine, install a socket
type oil filter wrench (Figure 12) squarely over the
oil filter and loosen it counterclockwise. Quickly remove
the oil filter as oil will begin to run out of it.
c. Hold the filter over the drain pan and pour out the
remaining oil. Place the filter in a plastic bag, seal
the bag and dispose of it properly.
d. Thoroughly wipe off all oil that drained onto the top
surface of the left crankcase half. Clean with a contact
cleaner to eliminate all oil residue from the engine
prior to installing the new oil filter.
e. Coat the gasket on the new filter with clean oil.
CAUTION
Tighten the oil filter by hand. Do not
overtighten.
f. Screw the oil filter onto its mount by hand and
tighten it until the filter gasket touches the sealing
surface, then tighten the filter by hand an additional
1/2 to 3/4 turn.
6. Remove the oil tank drain plug and gasket. Wipe the
drain plug sealing surface on the frame rail pan with a
clean, lint-free cloth.
7. Replace the engine oil tank drain plug O-ring (Figure
13) if it is leaking or damaged.
8. Lubricate the O-ring with clean engine oil before installing
it. Then screw in the drain plug and O-ring, and
tighten to 14-21 ft.-lb. (19-29 N•m).
CAUTION
Do not overfill the engine in Step 9. If too
much oil is added, the filler cap will be forced
out of the oil tank casewhen the oil gets hot.
9. Add the correct viscosity (Table 3) and quantity (Table
4) of oil to the oil tank case. Insert the oil filler cap into
the case and push it down until it bottoms.
NOTE
After oil has been added, the oil level will
register above the upper groove dipstick
mark (Figure 6) until the engine runs and
the filter fills with oil. To obtain a correct
reading after adding oil and installing a
new oil filter, follow the procedure in Step
10.
5. To replace the oil filter (Figure 11), performthe following:
a. Temporarily install the drain bolt and O-ring, and
tighten the bolt finger-tight. Then move the drain
pan underneath the front portion of the crankcase
and the oil filter.
b. At the front left side of the engine, install a socket
type oil filter wrench (Figure 12) squarely over the
oil filter and loosen it counterclockwise. Quickly remove
the oil filter as oil will begin to run out of it.
c. Hold the filter over the drain pan and pour out the
remaining oil. Place the filter in a plastic bag, seal
the bag and dispose of it properly.
d. Thoroughly wipe off all oil that drained onto the top
surface of the left crankcase half. Clean with a contact
cleaner to eliminate all oil residue from the engine
prior to installing the new oil filter.
e. Coat the gasket on the new filter with clean oil.
CAUTION
Tighten the oil filter by hand. Do not
overtighten.
f. Screw the oil filter onto its mount by hand and
tighten it until the filter gasket touches the sealing
surface, then tighten the filter by hand an additional
1/2 to 3/4 turn.
6. Remove the oil tank drain plug and gasket. Wipe the
drain plug sealing surface on the frame rail pan with a
clean, lint-free cloth.
7. Replace the engine oil tank drain plug O-ring (Figure
13) if it is leaking or damaged.
8. Lubricate the O-ring with clean engine oil before installing
it. Then screw in the drain plug and O-ring, and
tighten to 14-21 ft.-lb. (19-29 N•m).
CAUTION
Do not overfill the engine in Step 9. If too
much oil is added, the filler cap will be forced
out of the oil tank casewhen the oil gets hot.
9. Add the correct viscosity (Table 3) and quantity (Table
4) of oil to the oil tank case. Insert the oil filler cap into
the case and push it down until it bottoms.
NOTE
After oil has been added, the oil level will
register above the upper groove dipstick
mark (Figure 6) until the engine runs and
the filter fills with oil. To obtain a correct
reading after adding oil and installing a
new oil filter, follow the procedure in Step
10.
) een drainplug van de tank naar buiten toe onderaan het frame
Vergelijkbare onderwerpen
